1.Introduction
1.1.Description
1.2.Box Contents
1.3.Features
1.4.Application Diagram
1.4.1.Collaboration Room
1.4.2.Dual Screen Application
1.4.3.Auditorium
2.Product Overview
2.1.Front and Rear View
2.2.Front and Rear Panel LEDs
2.2.1.Device Status LED
2.2.2.Gigabit Ethernet Status LEDs
2.3.Button Functions
3.Installation
3.1.Mounting Options - Compatibility Table
3.2.Electrical Connections
3.2.1.DC 12V Input Connector
3.2.2.DC 5V Input Connector
3.2.3.USB Connectors
3.2.4.Ethernet Connectors
3.2.5.OCS Connector
3.2.6.GPIO - General Purpose Input/Output Ports
3.2.7.RS-232 Connector
3.3.Connecting Steps
3.4.Ethernet Switch - Detailed Requirements
4.CATx Cable Diagnostics for TPN Endpoints
4.1.Bandwidth Requirement of SDVoE Technology
4.2.Maximum Cable Extensions
4.3.Recommended CATx Cable Types
4.4.Testing the Reliability of the Cabling
4.5.Keystones
4.6.Tips & Tricks for the Best TPX/TPN Experience
5.Device Concept
5.1.The Control Unit (CTU)
5.2.Control Features
5.2.1.Ethernet Interface
5.2.2.Serial Interface
5.3.AV Management
5.3.1.Example for Point-Multipoint Connection
5.4.Ethernet Interface
5.5.Lightware Advanced Room Automation (LARA)
5.5.1.Opening the LARA interface
5.5.2.Running LARA
5.5.3.Downloading/Uploading a Configuration
5.5.4.Status Board
5.5.5.Touch Panel Support
5.5.6.Limitations and Capabilities
5.6.Basic Network Security
5.6.1.Disable Ethernet Ports
5.6.2.HTTP/HTTPS
5.6.3.Encryption (HTTPS, WSS)
5.7.802.1x Authentication
5.8.WebSocket Service (WS, WSS)
5.9.Advanced Ethernet Security
5.9.1.Network Separation
5.10.Serial Interface
5.10.1.Serial Port Diagram
5.10.2.Serial Options - Example
5.11.GPIO Interface
5.12.OCS Interface
5.13.Further Built-in Features
6.AV System Configuration - Step by Step
6.1.TPN / OPTN System Configuration Document
7.Software Control - Built-in Web
7.1.Establishing the Connection
7.2.The Layout of the Built-in Web
8.Software Control - Lightware Device Controller
8.1.Install and Update
8.2.Running the LDC
8.3.Establishing the Connection
8.4.Control Menu
8.4.1.Ethernet Tab
8.4.2.GPIO
8.4.3.OCS - Occupancy Sensor
8.4.4.RS-232
8.5.Settings Menu
8.5.1.Status
8.5.2.Network
8.5.3.Service
8.5.4.System
8.6.Advanced View Window
9.Software Control - BlueRiver AV Manager
9.1.Introduction
9.2.TPN / OPTN System Configuration Document
10.Lightware REST API Reference
10.1.Overview
10.2.Instructions for the Terminal Application Usage
10.2.1.Web Browser Plugins
10.2.2.Terminal Application
10.3.Protocol Rules
10.3.1.Command Structure Example
10.3.2.General Rules
10.3.3.Legend for the Control Commands
10.3.4.Lightware REST API vs. LW3 Protocol
10.3.5.Method Types
10.3.6.Supported Commands
10.3.7.Not Supported Commands
10.3.8.Status Codes, Error Messages
10.3.9.Polling
10.4.REST API Security
10.4.1.Authentication
10.4.2.Encryption (HTTPS)
10.5.System Commands
10.5.1.Setting the Device Label
10.5.2.Restarting the Device
10.5.3.Restoring the Factory Default Settings
10.5.4.Querying the Firmware Package Version
10.5.5.Control Lock
10.5.6.Setting the Current Time
10.5.7.Identifying the Device
10.5.8.Toggling the Dark Mode Setting
10.5.9.Setting the Delay of the Dark Mode
10.6.Ethernet Port Configuration
10.6.1.Setting the DHCP State
10.6.2.Changing the IP Address (Static)
10.6.3.Changing the Subnet Mask (Static)
10.6.4.Changing the Gateway Address (Static)
10.6.5.Applying Network Settings
10.6.6.Setting the Hostname
10.7.Network Security
10.7.1.Enabling/Disabling Ethernet Port
10.7.2.Querying Network Service Port Number
10.7.3.Enabling/Disabling Network Service Port
10.7.4.Querying the Username for Authentication
10.7.5.Setting Password for Authentication
10.7.6.Enabling Authentication
10.8.Serial Port Configuration
10.8.1.BAUD Rate Setting
10.8.2.Stop Bits Setting
10.8.3.Querying Data Bits
10.8.4.Parity Setting
10.8.5.Querying the Serial over IP Port Number
10.8.6.Enabling the Serial over IP Port
10.9.Serial Port Messaging
10.9.1.Sending a Message via RS-232
10.10.GPIO Port Configuration
10.10.1.Setting the Direction of a GPIO Pin
10.10.2.Setting the Output Level of a GPIO Pin
10.10.3.Setting the Output Level for a Specified Time
10.10.4.Toggling the Level of a GPIO Pin
10.11.OCS Port Configuration
10.11.1.Querying the Input Level of an OCS Pin
10.11.2.Setting the Sensor Type
10.11.3.Querying the Reported OCS State
10.12.Updating the Device via REST API
10.12.1.Querying the Update REST API Version
10.12.2.The Updating Process
10.12.3.Uploading the Package
10.12.4.Configuration Parameters – Keep the Current Settings
10.12.5.Executing the Update
10.12.6.Querying the State of the Updating Process
10.13.Lightware REST API - Quick Summary
11.LW3 Programmers Reference
11.1.Overview
11.2.Instructions for the Terminal Application Usage
11.3.Websocket (WS) or Secured Websocket (WSS) Usage
11.4.Protocol Rules
11.4.1.LW3 Tree Structure and Command Structure (examples)
11.4.2.General Rules
11.4.3.Legend for the Control Commands
11.4.4.Command Types
11.4.5.Prefix Summary
11.4.6.Error Messages
11.4.7.Escaping
11.4.8.Signature
11.4.9.Subscription
11.4.10.Notifications about the Changes of the Properties
11.5.System Commands
11.5.1.Setting the Device Label
11.5.2.Resetting the Device
11.5.3.Restoring the Factory Default Settings
11.5.4.Querying the Firmware Package Version
11.5.5.Control Lock
11.5.6.Setting the Current Time
11.5.7.Identifying the Device
11.5.8.Toggling the Dark Mode Setting
11.5.9.Setting the Delay of the Dark Mode Setting
11.6.Ethernet Port Configuration
11.6.1.Setting the DHCP State
11.6.2.Changing the IP Address (Static)
11.6.3.Changing the Subnet Mask (Static)
11.6.4.Changing the Gateway Address (Static)
11.6.5.Applying Network Settings
11.6.6.Setting the Hostname
11.7.Network Security
11.7.1.Enabling/Disabling Ethernet Port
11.7.2.Querying the Service Port Number
11.7.3.Enabling/Disabling Service Port
11.7.4.Querying the Username for Authentication
11.7.5.Setting a Password for Authentication
11.7.6.Enabling Authentication
11.7.7.Restarting Network Services
11.8.Serial Port Configuration
11.8.1.BAUD Rate Setting
11.8.2.Stop Bits Setting
11.8.3.Querying Data Bits
11.8.4.Parity Setting
11.9.Sending a Message via RS-232
11.10.GPIO Port Configuration
11.10.1.Querying the Direction of a GPIO Pin
11.10.2.Setting the Direction of a GPIO Pin
11.10.3.Querying the Output Level of a GPIO Pin
11.10.4.Setting the Output Level of a GPIO Pin
11.10.5.Setting the Output Level for a Specified Time
11.10.6.Toggling the Level of a GPIO Pin
11.11.OCS Port Configuration
11.11.1.Querying the Input Level of an OCS Pin
11.11.2.Setting the Sensor Type
11.11.3.Querying the Reported OCS State
12.Firmware Update
12.1.Introduction
12.2.Preparation
12.2.1.Reserved Ports of the SDVoE Control Server
12.2.2.About the Firmware Package (LFP2 File)
12.2.3.LDU2 Installation
12.3.Running the Software
12.4.The Updating Steps
12.5.Device IP Change in the CTU during Firmware Update
12.5.1.MAC Address Expansion
12.5.2.Issues During Update
12.6.Updating Via GUI
12.7.Command Line Interface (CLI)
12.7.1.How to Run
12.7.2.How to Use
12.8.CLI Commands
12.8.1.Help
12.8.2.LDU2 Version
12.8.3.Check For New LDU2 Version
12.8.4.Device Info
12.8.5.Update
12.8.6.Package Options
12.8.7.Complex Example
12.8.8.Exit Codes
12.9.Updating via REST API
12.10.If the Update is not successful
13.Troubleshooting
13.1.Use Cases
13.2.How to Speed Up the Troubleshooting Process
14.Technologies
14.1.EDID Management
14.1.1.Understanding the EDID
14.1.2.Advanced EDID Management
14.2.HDCP Management
14.2.1.Protected and Unprotected Content
14.2.2.Disable Unnecessary Encryption
14.2.3.HDCP 2.2
14.3.Pixel Accurate Reclocking
14.4.AV Over IP
14.4.1.Basics
14.4.2.What is TCP/IP?
14.4.3.Multicast DNS (mDNS) Protocol
15.Appendix
15.1.Specification
15.2.Port Numbering
15.3.Factory Default Settings
15.4.Content of the Backup File (Clone Configuration)
15.5.Mechanical Drawings
15.5.1.TPN Control Unit
15.6.Reserved Ports and Security Options
15.7.Cable Wiring Guide
15.7.1.Serial Ports
15.7.2.Audio Ports
15.7.3.OCS Sensor
15.8.Release Notes of the Firmware Packages
15.9.Hashtag Keyword List
15.10.Further Document Information
15.11.Limited Warranty Statement
TPN-CTU-X50
